File Manager

Editing File: /usr/sbin/raid-check

#!/bin/bash
#
# This script reads it's configuration from /etc/sysconfig/raid-check
# Please use that file to enable/disable this script or to set the
# type of check you wish performed.

# We might be on a kernel with no raid support at all, exit if so
[ -f /proc/mdstat ] || exit 0

# and exit if we haven't been set up properly
[ -f /etc/sysconfig/raid-check ] || exit 0
. /etc/sysconfig/raid-check

# Wait until no more than arg1 arrays in arg2 list are busy
waitbusy() {
    local threshold=$(($1 + 1))
    local dev_list="$2"
    while true
    do
	local busy=0
	local dev=""
	for dev in $dev_list; do
	    local sync_action=`cat /sys/block/$dev/md/sync_action`
	    if [ "$sync_action" != "idle" ]; then
		let busy++
	    fi
	done
        [ $busy -lt $threshold ] && break
	sleep 60
    done
}

[ "$ENABLED" != "yes" ] && exit 0

case "$CHECK" in
    check) ;;
    repair) ;;
    *) exit 0;;
esac

ionice=""
renice=""
case $NICE in
    high)
	renice="-n -5"
	;;
    low)
	renice="-n 5"
	ionice="-c2 -n7"
	;;
    idle)
	renice="-n 15"
	ionice="-c3"
	;;
    *)
	;;
esac

active_list=`grep "^md.*: active" /proc/mdstat | cut -f 1 -d ' '`
[ -z "$active_list" ] && exit 0

declare -A check
dev_list=""
check_list=""
for dev in $active_list; do
    echo $SKIP_DEVS | grep -w $dev >&/dev/null && continue
    if [ -f /sys/block/$dev/md/sync_action ]; then
	# Only perform the checks on idle, healthy arrays, but delay
	# actually writing the check field until the next loop so we
	# don't switch currently idle arrays to active, which happens
	# when two or more arrays are on the same physical disk
	array_state=`cat /sys/block/$dev/md/array_state`
	if [ "$array_state" != "clean" -a "$array_state" != "active" ]; then
	    continue
	fi
	sync_action=`cat /sys/block/$dev/md/sync_action`
	if [ "$sync_action" != idle ]; then
	    continue
	fi
	ck=""
	echo $REPAIR_DEVS | grep -w $dev >&/dev/null && ck="repair"
	echo $CHECK_DEVS | grep -w $dev >&/dev/null && ck="check"
	[ -z "$ck" ] && ck=$CHECK
	dev_list="$dev_list $dev"
	check[$dev]=$ck
	[ "$ck" = "check" ] && check_list="$check_list $dev"
    fi
done
[ -z "$dev_list" ] && exit 0

for dev in $dev_list; do
    #Only run $MAXCONCURRENT checks at a time
    if [ -n "$MAXCONCURRENT" ]; then
	waitbusy $((MAXCONCURRENT - 1)) "$dev_list"
    fi
    echo "${check[$dev]}" > /sys/block/$dev/md/sync_action

resync_pid=""
    wait=10
    while [ $wait -gt 0 -a -z "$resync_pid" ]; do
	sleep 6
	let wait--
	resync_pid=$(ps -ef | awk -v mddev=$dev 'BEGIN { pattern = "^\\[" mddev "_resync]$" } $8 ~ pattern { print $2 }')
    done
    [ -n "$resync_pid" -a -n "$renice" ] &&
    	renice $renice -p $resync_pid >&/dev/null
    [ -n "$resync_pid" -a -n "$ionice" ] &&
    	ionice $ionice -p $resync_pid >&/dev/null
done
[ -z "$check_list" ] && exit 0

waitbusy 0 "$check_list"

for dev in $check_list; do
	mismatch_cnt=`cat /sys/block/$dev/md/mismatch_cnt`
	# Due to the fact that raid1/10 writes in the kernel are unbuffered,
	# a raid1 array can have non-0 mismatch counts even when the
	# array is healthy.  These non-0 counts will only exist in
	# transient data areas where they don't pose a problem.  However,
	# since we can't tell the difference between a non-0 count that
	# is just in transient data or a non-0 count that signifies a
	# real problem, simply don't check the mismatch_cnt on raid1
	# devices as it's providing far too many false positives.  But by
	# leaving the raid1 device in the check list and performing the
	# check, we still catch and correct any bad sectors there might
	# be in the device.
	raid_lvl=`cat /sys/block/$dev/md/level`
	if [ "$raid_lvl" = "raid1" -o "$raid_lvl" = "raid10" ]; then
	    continue
	fi
	if [ "$mismatch_cnt" -ne 0 ]; then
		echo "WARNING: mismatch_cnt is not 0 on /dev/$dev"
	fi
done

Back to Directory File Manager